FIRETROL电动消防泵控制器FTA1930简介
Firetrol FTA1930数字固态启动消防泵控制器具有软启动，软停止和系统感应功能，不仅可以降低电流启动，还可以提供更高水平的机械性能。控制器监视，显示和记录消防泵系统信息。
当调用运行时，电机将从电机FLA的100％开始加速，最大为300％FLA，同时额定转矩降至15％。停止时，电机将减速至预设水平并暂停，如果需要，可以重新启动，从而限制管道系统的压力。如果没有其他启动原因，电机将继续减速至完全停止。该控制器有助于减少系统中的水锤。
认证：美国保险商实验室公司根据UL218，消防泵控制器标准，CSA，工业控制设备标准，并由Factory Mutual批准，列出Firetrol消防泵控制器。它们的制造符合或超出了审批机构以及NEMA和最新版本的NFPA 20，安装离心式消防泵和NFPA 70，国家电气规范的要求。
标准功能：以下是每个控制器的标准配置：
•电压浪涌保护器
•主断开开关，适用于连接的电机马力和电压
•消防泵断路器
•单手柄隔离断开开关/断路器机构
•电机接触器
•紧急手动运行机制，在紧急情况下机械关闭电机接触器触点
•内置启动和停止按钮，可绕过自动启动电路
•最小运行定时器/关闭延迟定时器
Description—Firetrol® FTA1930 Digital Solid State Starting Fire Pump Controllers feature soft start, soft stop and system sensing capabilities that not only provide for reduced current starting, but also offer an improved level of hydro mechanical performance. The controller monitors, displays and records fire pump system information.
When called to run, the motor will accelerate beginning at 100% of motor FLA up to a maximum of 300% FLA while rated torque is reduced to 15%. When stopping, the motor will decelerate to a preset level and pause, allowing for a restart if required, limiting stress in the piping system. If no additional starting causes are present, the motor will continue to decelerate to a full stop. This controller helps to reduce water hammer in the system.
Approvals – Firetrol fire pump controllers are listed by Underwriters’ Laboratories, Inc., in accordance with UL218, Standard for Fire Pump Controllers, CSA, Standard for Industrial Control Equipment, and approved by Factory Mutual. They are built to meet or exceed the requirements of the approving authorities as well as NEMA and the latest editions of NFPA 20, Installation of Centrifugal Fire Pumps, and NFPA 70, National Electrical Code.
Standard Features—The following are included as standard with each controller:
Voltage surge protector
Main Disconnect Switch sized for connected motor horsepower and voltage
Fire pump Circuit Breaker
Single handle Isolating Disconnect Switch/Circuit Breaker mechanism
Motor contactor
Emergency Manual Run Mechanism to mechanically close motor contactor contacts in an emergency condition
Built-in Start and Stop push-buttons to bypass automatic start circuits
Minimum Run Timer / Off Delay Timer
FIRETROL电动消防泵控制器FTA1930特点
特殊外壳
-T NEMA型3R（IEC IP22），彩涂钢
-E NEMA 4型（IEC IP66），彩涂钢
-F NEMA型4X（IEC IP66），γ304不锈钢，
-FXP NEMA型4X（IEC IP66），γ304不锈钢，涂漆
-FD NEMA型4X（IEC IP66），γ316不锈钢，
-FDB NEMA型4X（IEC IP66），12规格，接缝焊接，γ- 316不锈钢，抛光和刷光整理
-FDP NEMA型4X（IEC IP66），α316不锈钢
-G NEMA 12型（IEC IP54），彩涂钢
断路器选项
-N中间额定值150000安培RMS Sym。
-P高耐受性200000安培RMS Sym
注意：对于所有马力和电压，中等和高额定值可能不可用。咨询工厂是否可用。
防冷凝空间加热器
-H 120伏空间加热器
-J 120伏特空间带恒温器的加热器
-K 120伏特空间湿度调节器
-L 240伏空间加热器
-M 240伏特空间带恒温器的加热器
-N 240伏特空间湿度调节器
压力传感器
-B 600 PSI（0～42.25巴）淡水压力传感器铜腐蚀服务用
-C 0-300 PSI（0～21.1巴）压力传感器
-D 0-600 PSI（0～42.25巴）腐蚀性压力传感器
组合式自动功率转换开关
FTA950发电机/公用事业应急电源
FTA951 -发电机/公用事业应急电源旁路隔离
警告
-AC 用于远程指示的交流额外触点（常开和常闭），泵操作
-AF声光低泵室温度报警器
-AG银声可见储层低报警
-AH可听和可见低吸气压力报警器
-AM用于远程指示的AM触点，泵启动失败
-AV接触远程指示，低泵室温（需要选项-AF）
-AW接触远程指示，水库低（需要选项-AG）
-AY触点，用于远程指示，低吸气压力（需要选项-AH）
-AZ低泵室温开关，已安装和接线
-BW用于远程指示，相位故障/相位反转的额外触点
-BY用于远程指示，泵过载的触点
-COM低吸气压力报警，（包括可选择的自动/手动复位，声音，可见和远程报警，不包括启动压力开关）
-CTS内置低吸气压力报警面板（包括可选择的自动/手动复位，声音，可见和远程报警以及有线和安装压力开关）
-EG声光和可见安全阀放电报警
-EH触点，用于远程指示，安全阀放电（需要选件-EG）
-EJ声音和可见流量计报警
-EK用于远程指示，流量计接触的触点（需要选项-EJ）
-KH用于远程指示的触点，任何报警的通用输出
-JR可见赛马泵运行指示
-JT声音和可见的赛马泵故障指示
-P内置报警系统（包括可见监控电压正常指示和声音泵操作，相位故障和相位反转指示）
-PE触点，用于远程指示，低系统压力（按需泵）
-PT内置报警系统，220 VAC监控电源（包括可见监控电压正常指示和声音泵操作，相位故障和相位反转指示）
杂项
-ED减载电路（可选择的电源和可调节的时间延迟，以便在启动前移除非关键负载）
-EL系列泵，高区控制器
-EM系列泵，中区控制器
-EN系列泵，低区控制器
-FZX 400 VAC操作（控制器标记为在380-400 VAC下操作 - 使用电压代码FZ）
-IEC CE标记与外部安装的湿部件
-IECI CE标记内部安装的湿部件
-OSP OSHPD抗震认证（加利福尼亚州）（需要选项-SEI）
-PY电机空间加热器输出触点
-S热带化
-SEI抗震认证（符合IBC）（注：不适用于型号FTA1500）
-USBX外部USB端口
-ZPA定制的年度服务显示信息（在启动时由Firetrol代表进行工厂编程或编程）
-ZPN使用5150连接模块通过以太网TCP / IP串行Modbus RTU
-ZPM串行Modbus RTU，采用2线或4线RS485出口包装（木箱符合IPPC标准）
SPECIAL ENCLOSURES
-T NEMA Type 3R (IEC IP22), Painted Steel
-E NEMA Type 4 (IEC IP66), Painted Steel
-F NEMA Type 4X (IEC IP66), #304 Stainless Steel,
Unfinished**
-FXP NEMA Type 4X (IEC IP66), #304 Stainless Steel,
Painted Finish
-FD NEMA Type 4X (IEC IP66), #316 Stainless Steel,
Unfinished**
-FDB NEMA Type 4X (IEC IP66), 12 Gauge, Seam
Welded, #316 Stainless Steel, Polished and
Brushed Finish
-FDP NEMA Type 4X (IEC IP66), #316 Stainless Steel
Painted Finish
-G NEMA Type 12 (IEC IP54), Painted Steel
** Unfinished (Not painted, polished or brushed).
CIRCUIT BREAKER OPTION
-N Intermediate withstand rating
150,000 Amps RMS Sym.
-P High withstand rating
200,000 Amps RMS Sym
Note: Intermediate and High withstand ratings may not be available for all horsepowers and voltages. Consult factory for availability.
ANTI-CONDENSATION SPACE HEATERS
-H 120 Volt Space Heater
-J 120 Volt Space Heater With Thermostat
-K 120 Volt Space Heater With Humidistat
-L 240 Volt Space Heater
-M 240 Volt Space Heater With Thermostat
-N 240 Volt Space Heater With Humidistat
PRESSURE TRANSDUCERS
-B 0-600 psi (0-42.25 bar) Pressure Transducer for
Fresh Water Service
-C 0-300 psi (0-21.1 bar) Pressure Transducer for
Copper Corrosive Service
-D 0-600 psi (0-42.25 bar) Pressure Transducer for
Corrosive Service
COMBINED AUTOMATIC POWER TRANSFER SWITCHES
FTA950 - Generator/Utility emergency source
FTA951 - Bypass Isolation for Generator/Utility emergency source
ALARMS
-AC Extra contacts (normally open & normally closed) for remote indication, pump operating
-AF Audible and Visible low pump room temperature alarm
-AG Audible and Visible reservoir low alarm
-AH Audible and Visible low suction pressure alarm
-AM Contacts for remote indication, pump fail to start
-AV Contacts for remote indication,
low pump room temperature (Requires option -AF)
-AW Contacts for remote indication, reservoir
low (Requires option -AG)
-AY Contacts for remote indication, low suction pressure (Requires option -AH)
-AZ Low pump room temperature switch, mounted and wired
-BW Extra contacts for remote indication,
phase failure/phase reversal
-BY Contacts for remote indication, pump overload
-COM Low Suction Pressure Alarm, (Includes selectable auto/manual reset, audible, visible and remote alarms, initiating
pressure switch NOT included)
-CTS Built-in Low Suction Pressure Alarm
Panel (Includes selectable auto/manual reset, audible, visible and remote alarms and wired and mounted pressure
switch)
-EG Audible and Visible relief valve discharge alarm
-EH Contacts for remote indication, relief valve discharge (Requires option -EG)
-EJ Audible and Visible flow meter on alarm
-EK Contacts for remote indication, flow meter on (Requires option -EJ)
-KH Contacts for remote indication, common output for any alarm
-JR Visible jockey pump running indication
-JT Audible and Visible jockey pump trouble indication
-P Built-in alarm system (Includes visible supervisory voltage normal indication and audible pump operating, phase failure and phase reversal indication)
-PE Contacts for remote indication, low system pressure (pump on demand)
-PT Built-in alarm system, 220 VAC supervisory power (Includes visible supervisory voltage normal indication and audible pump operating, phase failure and phase reversal indication)
MISCELLANEOUS
-ED Load shed circuits (Selectable power source and adjustable time delay to remove non-critical loads before starting)
-EL Series pumping, high zone controller
-EM Series pumping, mid zone controller(s)
-EN Series pumping, low zone controller
-FZX 400 VAC Operation (Controller labeled for operation at 380-400 VAC - Use with voltage code FZ)
-IEC CE Marking with Externally Mounted Wet Parts
-IECI CE Marking with Internally Mounted Wet Parts
-OSP OSHPD Seismic Certification (State of California) (Requires Option -SEI)
-PY Motor space heater output contacts
-S Tropicalization
-SEI Seismic Certification (in accordance with IBC)
(Note: Not available on model FTA1500)
-USBX External USB Port
-ZPA Customized, annual service display message (when factory programmed or programmed by Firetrol representative
during start-up)
-ZPN Serial Modbus RTU over Ethernet TCP/IP using 5150 Connectivity Module
-ZPM Serial Modbus RTU over 2-wire or 4-wire RS485
Export packaging (Wooden crating to conform
to IPPC Standards)
FIRETROL电动消防泵控制器FTA1930
爱泽工业(IZE INDUSTRIES)特价经销、常用备件FIRETROL电动消防泵控制器系列列表：
FIRETROL电动消防泵控制器FTA760
FIRETROL电动消防泵控制器FTA1000
FIRETROL电动消防泵控制器FTA1600
FIRETROL电动消防泵控制器FTA1800
FIRETROL电动消防泵控制器FTA2000
FIRETROL电动消防泵控制器FTA2400
FIRETROL电动消防泵控制器FTA1260
FIRETROL电动消防泵控制器FTA1300
FIRETROL电动消防泵控制器FTA1930
FIRETROL电动消防泵控制器FTA900
FIRETROL电动消防泵控制器FTA976
FIRETROL电动消防泵控制器FTA950
FIRETROL电动消防泵控制器FTA1100-K2
FIRETROL电动消防泵控制器FTA1100-JL24N
FIRETROL电动消防泵控制器FTA1100-JL12N
爱泽工业成立于2010年，定位于向先进制造工业提供高端制造技术和设备。代理经营世界先进的电气自动化、机械与传动、流体控制、仪器仪表、工具等产品。作为电气，液压以及气动解决方案的合作伙伴，我们利用我们的全球协作团队，为客户提供先进解决方案，市场知识以及相关增值服务来帮助优化客户的工作效率，提高可靠性和安全性，致力于成为工业产品和解决方案的优质渠道。
如果有任何关于FIRETROL电动消防泵控制器FTA1930的疑问，请随时与我们联系（021-31006702）。我们将尽全力解决您的问题。
有关FIRETROL电动消防泵控制器FTA1930更详细的信息或者购买FIRETROL相关产品，请联系爱泽工业。
If you have any question, please feel free to dial 0086-21-3100 6702 or browse our website: www.ize-industries.com.
FIRETROL电动消防泵控制器FTA1930简介及特点
