SEMAR/ROVER齿轮泵NOVAX-G系列简介
“G”系列电动齿轮泵专为转移所有非侵蚀性日常粘性液体而开发，其粘度在40°之间介于1°Engler之间（例如：水，油 - 仅间歇性工作以防止过热）和7°Engler（SAE 30发动机油或SAE 80变速箱油）。液体必须清洁，没有悬浮颗粒。这些泵适用于水，葡萄酒，橄榄油，牛奶或柴油以及合成油或矿物油的转移。
电动齿轮泵能够在不需要填充的情况下将液体吸入最大2米的液位差。如果下降差异较大，则可以在吸入管的末端设置止回阀，然后必须将其填充到泵的位置。为了增加泵的抽吸能力，将大约10毫升的液体倒入泵中。在任何情况下，泵应该靠近待转移液体的容器放置。如果干燥超过10秒，泵可能会损坏。切勿在没有软管接头的情况下操作泵。
在启动泵之前，务必连接随吸管提供的过滤器。
如果使用安全阀代码920035，齿轮泵只能与输送手枪一起使用。
所有型号均可在2 bar（0.2 MPa）的压力下连续运行。
230V动力型号配备一个换向器，可以反转电机的旋转，从而可以自由选择泵送方向。
电池供电的型号具有预定的旋转方向，该旋转方向由泵壳上的箭头指示。
齿轮选择：
您可以要求泵配有不锈钢齿轮或PTFE。
不锈钢齿轮：理想情况下，您应该要求合成油的转移，粘度在ISO VG 80和150之间; 有点吵，但它们的使用寿命很长。
PTFE齿轮：低粘度油（ISO VG 32和80之间）必须使用，最大冷滗析。30°C，也可连续使用但自由放电（排气压力低于0.1 BAR）
注意：与所有的电动泵一样，即使是齿轮也不能在没有液体的情况下干燥或长时间运行。
The “G” series electric gear pumps have been developed for the transfer of all non-aggressive everyday viscous liquids, the viscosity of which at 40° is between 1° Engler (example: water, oil - only intermittent duty to prevent overheating) and 7° Engler (SAE 30 engine oil or SAE 80 gearbox oil). The liquids must be clean without suspended particles. These pumps are suitable for the transfer of water, wine, olive-oil, milk or diesel and synthetic or mineral oil.
The electric gear pumps are capable of sucking liquids up to a maximum drop difference of 2 meters without the need of filling. If the drop difference is greater, a non-return valve can be positioned at the end of the suction pipe which must then be filled as far as the pump. To increase the suction capacity of the pump, pour approximately 10 ml of the liquid to be transferred into the pump. The pump should in any case be positioned close to the container of the liquid to be transferred. The pump could be damaged if it runs dry for more than 10 seconds. Never operate the pump without the hose connectors.
Always connect the filter supplied with the suction pipe before starting the pump.
The gear pumps can only be used with the delivery pistol if a safety valve code 920035 is used.
All models can operate in a continuous manner at a pressure of 2 bar (0.2 MPa).
The 230V powered models are equipped with a commutator to reverse the rotation of the motor, which allows the free selection of the pumping direction.
The battery powered models have a predetermined rotation direction that is indicated by an arrow on the pump casing.
Gear choice.
You can request the pumps with stainless steel gear or PTFE.
Stainless Gears: ideally you should be requested for the transfer of synthetic oil, with a viscosity between ISO VG 80 and 150; a little noisy, but they have very long service life.
PTFE gears: shall be required for low viscosity oil (between ISO VG 32 and 80), cold decanted max. 30 ° C, also for continuous service but at free discharge (discharge pressure of less than 0.1 BAR)
Note: like all of our electric pumps, even the gear must not run dry or for prolonged periods in the absence of liquid.
SEMAR/ROVER齿轮泵技术资料
Code: 971000
Model: NOVAX G 20 HP 0.8
L / h: 1750
øD mm: 20
HP: 0.8
Hmax (m): 24
r.p.m.: 2850
A x B x H: 230X120H190
kg: 7
EAN code 8032706072380
SEMAR/ROVER齿轮泵NOVAX-G系列 示例NOVAX G 20 HP 0.6
爱泽工业(IZE INDUSTRIES)特价经销、常用备件SEMAR/ROVER列表：
SEMAR/ROVER齿轮泵NOVAX-G系列NOVAX G 20 HP 0.6
SEMAR/ROVER齿轮泵NOVAX-G系列NOVAX G 20 HP 0.8
爱泽工业成立于2010年，定位于向先进制造工业提供高端制造技术和设备。代理经营世界先进的电气自动化、机械与传动、流体控制、仪器仪表、工具等产品。作为电气，液压以及气动解决方案的合作伙伴，我们利用我们的全球协作团队，为客户提供先进解决方案，市场知识以及相关增值服务来帮助优化客户的工作效率，提高可靠性和安全性，致力于成为工业产品和解决方案的优质渠道。
如果有任何关于SEMAR/ROVER齿轮泵NOVAX-G系列 示例NOVAX G 20 HP 0.6的疑问，请随时与我们沟通（021-31006702）。我们将尽全力解决您的问题。
有关SEMAR/ROVER齿轮泵NOVAX-G系列 示例NOVAX G 20 HP 0.6更详细的信息或者购买意大利ROVER相关产品，请致电爱泽工业。
If you have any question, please feel free to dial 0086-21-3100 6702 or browse our website: www.ize-industries.com.
SEMAR/ROVER齿轮泵NOVAX-G系列简介
