气弹簧安装建议（中英文）

1、

气弹簧的设计温度范围为-20℃至+80℃。

Gas spring is designed for a temperature range of -20℃ to + 80℃.

2、

气弹簧内充满的是纯氮气，氮气属于惰性气体，不燃烧、不会爆炸、无毒。

Gas spring is filled with pure nitrogen, which is an inert gas, does not burn, will not explode and is not poisonous.

3、

气弹簧内含物处于高压状态！请勿打开或加热！

Gas spring contents under high pressure! Do not open or heat up!

4、

气弹簧内充满纯氮气和液压油，提供运动辅助。液压油用于润滑气弹簧内部零件，并具有阻尼功能。气弹簧杆上出现少量液压油是正常现象。

Gas Spring is filled with pure nitrogen & hydraulic oil and provides the motion assist. The Hydraulic Oil is used to lubricate gas spring inner parts and has the damper function. Some slight hydraulic oil appeared on the gas spring rod is a normal phenomenon.

5、

避免歪斜安装、倾斜或侧向和侧向力，因为这可能会损坏气弹簧并缩短其使用寿命。

Avoid askew installation, sloping or lateral and side force which may damage gas spring and shorten the lifetime.

6、

建议将活塞杆向下安装。此位置可确保最佳阻尼效果。

It is recommended to install with the piston rod downwards. This position ensures the best damping effect.

7、

气弹簧不应暴露在雨中或安装在潮湿和多尘的地方。

The gas spring should not be exposed to rain or installed in wet and dusty areas.

8、

气弹簧上不得附着油漆、油等异物。活塞杆应受到保护，避免受到冲击、划伤和弄脏。

No Foreigner materials such as paint, oil should be attached to the gas spring.And the piston rod should be protected against shocks, scratches and dirty.

9、

避免活塞杆螺纹破坏密封系统，请勿拆卸连接部件并将气弹簧压缩到超过最大行程长度。

Avoid the piston rod thread destroy the sealing system, do not dismantle the connecting part and compress the gas spring beyond the max stroke length.

10、

建议气弹簧完全压缩时，在行程上留出5~10mm的空间，以避免受到撞击。

Recommend to reserve 5~10mm space on stroke when full compressed gas spring to avoid impact.

11、

气弹簧在完全伸长时，不得加载牵引力，超过极限的过大拉力负载可能会损坏气弹簧。

Gas spring must not be loaded with traction force when it full extend. The high tension load beyond limit may damage the gas spring.

12、

建议仅在气弹簧位置旋转活塞杆，但不要频繁旋转，否则可能会破坏密封系统。

Recommend to rotate the piston rod only for gas spring position but not frequently which may destroy the sealing system.

13、

建议在建筑物或机械设备完工后进行安装，以确保气弹簧的清洁和使用寿命。

Recommend installation after building or machinery equipment finished to ensure  the clean of gas spring and lifetime.

14、

建议将气弹簧与附加锁定机制组装在一起，以避免不可抗力因素造成的危险。

Recommend to assemble the gas spring with additional locking mechanisms to avoid the danger caused by force majeure element.

15、

安装完成后，请勿将气弹簧用作抓手，以免气弹簧断裂或变形。

After installation finished, do not use gas spring as the grip to avoid break or deform gas spring.

16、

当气弹簧发生故障时，请停止使用并立即咨询厂家。请勿拆卸或焚烧气弹簧。

Stop use when gas spring break down and consult us immediately.Do not dismantle or incinerate gas spring.

17、

若不使用标准尺寸，而有特殊要求，可在所列范围内自行选择最佳尺寸。若对耐用性和稳定性要求很高，请避免（小直径+长行程+大力量）的组合。

If not using standard size, and you need special request, you can select your best dimensions yourself within the mentioned limits. If very high demands are placed on durability and stability. Please avoid the combination of (small diameter+ long stroke+ high force.)

.

18、

如果没有气弹簧使用经验或机构设计经验，请尽可能告知使用环境和条件。

Please advise us the environment of usage and conditions as possible if there is no experience on gas spring using or design on mechanism.

19、

建议不要将气弹簧存放超过 6 个月。第一次压缩气弹簧时可能会出现粘连效应，这可能需要比公称力更高的力。

Recommend not to store gas spring longer than 6 months. There may be sticking effect the first time you compress gas spring, which may require a higher force than the nominal force..

20、

力公差在 + 40N /- 20N 或公称力的 ± 5%~7% 之间。从物理上讲，气弹簧的实际力取决于温度，每 10℃ 变化约 3.5%。

Force tolerance between + 40N /- 20N or ± 5%~7% of nominal force. Physically,the actual force of gas spring depends on the temperature, for each 10℃ change about 3.5%.

21、

处理气弹簧前请采取安全措施，用直径2mm~3mm的钻头在底部钻一个约20mm~30mm的孔，待气弹簧内气体完全释放后再处理，并遵守当地的环保法规。

Take security measures before dispose the gas spring and use 2mm~3mm diameter drill to cut from the bottom about 20mm~30mm hole. Dispose the gas spring after the inner gas entirely releasing and obey local environmental regulation.

声明：